Empire Comfort Systems DVP48FP9(1 Manuel du propriétaire Page 11
- Page / 80
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
28649-2-0811 Page 11
REAR VENT CONVERSION
Converting ue take-off to rear venting
When switching out the ue and inlet vent collars to run horizontally
off the rear vent, the following steps must be taken.
1. Remove the inlet vent collar (8 screws) and ue collar (4 screws)
from the top of the replace, and set to the side.
2. Remove the inlet cover plate and ue cover plate located on
the back of the replace. These will be used to close the top
ue and inlet openings.
3. Insert the insulation retainer bracket and insulation into the top
ue pipe before reinstalling the ue cover plate over the top
ue with 4 screws.
4. Reinstall the inlet cover plate over the top inlet opening with 4
screws. See illustration above.
5. Install the ue collar assembly to the rear ue with 4 screws.
6. Install the inlet vent collar to the rear of the replace with 8
screws.
7. This completes the conversion for a rear vent application.
Note: For top vented installations, the insulation and retainer are
to be removed from the ue pipe and discarded.
VENT SYSTEMS
The following vent systems are acceptable for use with the
DVP (42,48) series replaces:
Simpson Duravent® GS 5" - 8", Refer to Page 37.
American Metal Products 5" - 8"
Selkirk Direct-Temp® 5" - 8"
Security Secure Vent® 5" - 8"
Empire Flexvent Kit DVVK-5F, Refer to Page 42.
The following vent systems are acceptable for use with the DVA-47
adaptor vertically off top of replace only:
Simpson Duravent
®
GS 4" - 6⅝", refer to page 36.
American Metal Products 4" - 6⅝"
Selkirk Direct-Temp® 4" - 6⅝"
Security Secure Vent® 4" - 6⅝"
Empire Horizontal Round Termination Kit DVVK-4RE, refer to page
30.
Empire Flexvent Kit DVVK-4F, refer to page 33.
Empire Direct Vent Kit DVVK-4FV, refer to page 21.
Note: Discard insulation
& retainer when using
vertical venting off
VERTICAL VENTING
HORIZONTAL VENTING
FLUE INSULATION
INSULATION
RETAINER
INLET VENT COLLAR
INLET VENT COLLAR
FLUE OUTLET
COLLAR
FLUE COVER PLATE
(See note above)
INLET VENT
COVER PLATE
FLUE COVER PLATE
INLET VENT
COVER PLATE
Note:Itis recommended that the
flue cover plate tab be pulled
outward prior to removal.
This will ensure that the plate
is not accidentally dropped
inside the rear air chamber.
Note: Discard insulation
& retainer when venting off
top of fireplace.
- INSTALLATION INSTRUCTIONS 1
- OWNER’S MANUAL 1
- TABLE OF CONTENTS 2
- SOME POINTS TO REMEMBER 4
- NO ODOR DETECTED - ODOR FADE 4
- LP-GAS WARNING ODOR 4
- INTRODUCTION 6
- SPECIFICATIONS 7
- FIREPLACE DIMENSIONS 7
- CLEARANCES 8
- LOCATING FIREPLACE 9
- GAS SUPPLY 10
- REAR VENT CONVERSION 11
- VENT SYSTEMS 11
- INSTALLATION 12
- INSTALLATION (continued) 13
- VENTING FIREPLACE - TOP 16
- EXAMPLES - TOP VENT RUN 19
- 28649-2-0811Page 20 20
- Figure 31 20
- Figure 32 20
- Figure 33 20
- Installation Instructions 21
- IMPORTANT SAFETY INFORMATION 21
- PRE-INSTALLATION INFORMATION: 22
- FLEX OUTER 23
- AIR INTAKE PIPE 23
- SPACER SPRINGS 23
- FLEX FLUE PIPE 23
- WING NUT (2) 24
- PIPE CLAMP 24
- ROOF BRACKET (2) 24
- SCREW (2) 24
- 1” (25mm) 25
- 35 ft. Max 26
- Vertical Flex Termination Kit 27
- VENTING FIREPLACE - REAR 28
- EXAMPLES - REAR VENT RUN 29
- DVA47 ADAPTOR 30
- OUTSIDE WALL 31
- VINYL SIDING KIT DV822 31
- OUTSIDE MOUNTING 31
- TERMINATION CLEARANCES 34
- VENT CLEARANCES 35
- VENT SYSTEM IDENTIFICATION 36
- WALL FIRESTOP 38
- HOLE IS OFF-SET 38
- TOWARDS BOTTOM 38
- OF WALL OPENING 38
- HORIZONTAL TERMINATION 41
- VERTICAL TERMINATION 43
- vertical 44
- LOG PLACEMENT (4 LOG SET) 45
- OPERATING INSTRUCTIONS 46
- STANDING PILOT WIRING DIAGRAM 48
- LIGHTING INSTRUCTIONS 49
- TO TURN OFF GAS TO FIREPLACE 49
- OPTIONAL REMOTE CONTROL 51
- TO TURN OFF GAS TO APPLIANCE 52
- PURGE PROCEDURE 53
- REGULATOR FITTING 55
- NOTE: STAMPED WITH 55
- GAS TYPE SET FOR USE 55
- Call Serviceman 58
- Spark generator off 59
- Second valve operator 59
- (Main) opens 59
- 28649-2-0811 Page 61 61
- Green LED Status Codes 62
- RF OPERATING INSTRUCTIONS 63
- RF MAINTENANCE INSTRUCTIONS 64
- RF WIRING DIAGRAM 65
- MAINTENANCE AND SERVICE 67
- DVP42FP(3,5,7,9) PARTS LIST 68
- DVP48FP(3,5,7,9) PARTS LIST 70
- PARTS VIEW 72
- MASTER PARTS DISTRIBUTOR LIST 73
- HOW TO ORDER REPAIR PARTS 73
- SEE NOTE* 74
- 110 VOLT AC 75
- Figure 94 76
- ACCESSORIES 77
- Fireplace Heater 78
- Comfor t Systems 80
Produits connexes et manuels pour Foyers Empire Comfort Systems DVP48FP9(1
(40 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.135 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels